Expert Answers about Chevrolet Electrical Tools

• How to Clean Dust Out of Performance Tool Electric Blower
• Performance Tool doesn't have any maintenance instructions for the Electric Blower # PTW50061 in the manual but when I reached out to my contact they suggested the following procedure: 1. Plug in 2. Turn knob to desired speed 3. Unplug and clean with a damp rag 4. Blow out with compressed air as needed Let me know if you have any additional questions about the electric blower!
  view full answer...


• Adjusting Electric Brake Assemblies on Trailer Drop Axle
• I'm not sure which brake adjustment tool you have but on our PT # W80630 there are two sides that can be used. The end with the 90 degree bend is designed for adjusting electric brakes on drop axles like yours, which will allow you to access that hard-to-reach star wheel adjuster. There's not really an additional trick or easier method for this process. I have attached a demonstration video below that you might also find helpful. You can skip ahead to the 4:35 mark to watch our installer...
  view full answer...


• Solution for Needing Manual Socket Tool for Atwood Powered A-Frame Jack
• That's really good info! Thanks for coming up with that and passing it on. I posted it here so that others in your situation could be helped by it.
  view full answer...


• How To Trim Underbody Panel on 2013 Honda CR-V For Installation of Curt Trailer Hitch # C13119
• To trim the underbody panel on your 2013 Honda CR-V for the installation of a Curt Trailer Hitch Receiver # C13119, I recommend marking the area that needs to be cut to start with. I have provided a graphic showing where this section is and the dimensions of the area that needs to be removed. I would then use the saw attachment for a rotary tool to cut the section from the underbody panel. I have provided a link to the instructions for this trailer hitch which provides you the types of...
  view full answer...


• Brake Adjustment Tool for Changing Braking Pressure on Electric Drum Brake
• It sounds like your four new manual-adjust trailer brakes just need some adjustment to get the appropriate tension on the drum surfaces. Since you hear the magnets humming you know you have correctly made the wiring connections. Electric drum brakes have a star wheel adjuster on their lower ends, close to the magnets. This is shown in the linked video at the 45-second mark and the opening to access the star wheel on the rear of the brake assembly is shown in the included photo. When adjusted...
  view full answer...


• How to Adjust Electric Drum Trailer Brakes with Video
• On electric drum brakes there is a star wheel at the bottoms of the assemblies that you can turn using a flat head screw driver or brake adjusting tool # W80630. Turning the wheel one way will bring the shoes closer in and turning it the other way pushes the shoes out more. You will adjust the brakes using that wheel until there is a slight but constant drag of the shoe pads on the drum. I have included a link to a video and at about the 4:39 mark our installed begins adjusting the brakes.
  view full answer...


• Is Demco DM9713093 Kar Kaddy Tow Dolly Shipped Fully Assembled
• The Demco # DM9713093 would be delivered partially assembled. The frame, the tongue, ramps and fenders are all sub-assemblies that would need to be installed to the dolly as discussed on page # 25 in the instructions I've linked for you. The tow dolly features a disc brake system that is superior to electric or hydraulic surge brakes and is the model I most often recommend. Assembling the dolly requires basic hand tools and is uncomplicated if the instructions are closely followed. Someone...
  view full answer...


• What Tools Are Needed to Install Thule Top Track Roof Mount System
• Yes, the installation instructions just have you installing the Thule Top Track Roof Mount System # THTP42 from the roof of the vehicle and not having to do anything on the inside. You will drill the holes in your roof using a 1/8" drill bit and then installing the M5 flare nut insert (see linked instructions). The 1/8" drill bit is included with the kit so the tools you need to have handy on your end (which are pretty common) include the following: Masking tape 9/16" Wrench Center punch Hammer Tape...
  view full answer...


• What Amperage Circuit does the Electric Scissor Jack Need for Proper Operation
• The Buffalo Tools Electric Car Jack, item # BTEJ212, is designed to run on the cigarette lighter circuit in the vehicle. I went out to my truck and checked that circuit and it is a 20 amp circuit. That means you will need at least a 20 amp ac to dc converter for proper function.
  view full answer...


• Who Can Convert a 2013 Dutchman Rubicon Trailer from Electric Drum Brakes to Hydraulic Disc Brakes
• Trailer brakes and vehicle brakes are very similar so a trusted mechanic could do the job. Other places to inquire include shops that work on trailers and RV dealers with a service center. We have a handy how-to article that covers everything needed to switch from electric brakes to hydraulic disc brakes. I have included a link to it for you.
  view full answer...


• How to Use the Lockout on the Titan Brake Actuator with Manual Lockout Part # T63FR
• In order to engage the reverse lockout on the Titan Brake Actuator with Manual Lockout part # T63FR you will need to insert the lockout tool which should be included, into the channel directly behind the coupler. I have pointed this channel out for you as well as the tool that is needed. If you don't have this tool then you will need to obtain this from the manufacturer. However, the other option you have is to add an electric lockout that will work when you place the tow vehicle into...
  view full answer...


• How to Adjust Electric Drum Brakes on Trailer
• To adjust brakes like the Dexter 7 Inch Electric Trailer Brake Assembly # 23-47 referenced in your question, you will use a flat head screwdriver to turn the star wheel located at the bottom of the assembly. You can also use a brake adjusting tool like # W80630. Turning the wheel one way will bring the shoes closer in and turning it the other way will push the shoe out. You will simply adjust the brakes using that wheel until there is a slight but constant drag of the shoe pads on the...
  view full answer...


• Is a Special Tool Required to Un-clip a Factory 7-Way Connector from the Vehicle Wiring
• There is not special tool required, but these connectors can be stubborn, especially with years of road grime built up. You may be able to make things easier on yourself by removing the receptacle from the rear bumper and giving yourself some slack. You may need to use a screw-driver to pry the locking tab up far enough to get the connector to release, be careful not to break the tab. If you do break the tab, you can wrap the connection in electrical tape to hold, but it will be more difficult...
  view full answer...


• Performance Tool Infrared Shop Heater Capacity
• The Performance Tool Infrared Shop Heater - Wall or Ceiling Mount - 1500 Watt # PTW5008 is not rated to heat a specific cubic foot area. The manufacturer says that it warms the area only directly in front of it or under it and will keep you warm about 10 feet away from it. The warmth will lessen as you get further away or to the sides of the unit. In general, a 1,500 watt heater offers an easy way to heat a small space. It generates that 1,500 watts of electricity per hour which produces...
  view full answer...


• How To Adjust Dexter Electric Trailer Brake Assembly
• The Dexter Electric Trailer Brake Assembly, # 23-438 (left side) # 23-439 (right side) when first installed require manual adjustment. Simply use a small screwdriver or similar tool to turn the adjustment wheel to push out the shoes. You will keep turning the wheel until the pads lightly, but consistently, drag on the drum. I've linked a video below, you can jump to the 4:40 mark for adjustment.
  view full answer...


• How to Initially Adjust the Dexter Nev-R-Adjust Electric Trailer Brakes
• The Dexter Nev-R-Adjust electric trailer brakes can be manually adjusted. There are a couple teeth of the adjustment wheel that are exposed just under the lever that you referenced. I have attached a photo showing the teeth. You will likely need a tool with a fine edge such as a flat head screw driver for the adjustment wheel on these brakes. A brake adjustment tool may be too thick. Without an initial manual adjustment, it could take a few braking attempts to adjust the brakes. I was...
  view full answer...


• How Does the Ultra-Fab Power Twin II Electric Stabilizer Install on a Trailer
• You will need to bolt on the Ultra-Fab Power Twin II Electric Stabilizer, # UF39-941705, using the included hardware. It bolts to the bottom of the frame on the travel trailer. You CAN do it. I believe in you. If you have the proper tools (drill, bits, wrenches) you can install this yourself at home. If you are not familiar with projects like this or have any reservations about performing the installation I do recommend having a professional install it. RV dealerships with service centers...
  view full answer...


• Waterproofing Electrical Connections on Optronics Boat Trailer Tail Lights
• The Waterproof, Over 80 inch Aero Pro Trailer Light Kit, # TL16RK, does contain the hardware needed for installation, but the lights and housing themselves are what is considered waterproof; they are sealed lights. The electrical connections for the wires are not waterproof. What you can do is apply something like Liquid Electrical Tape, # SWC50122, which will insulate, seal, and waterproof electrical connections. I would still recommend wrapping any connections with actual electrical...
  view full answer...


• How to Waterproof Trailer Light Connectors on a Nitro Boat Trailer
• What you can do is apply something like Liquid Electrical Tape, # SWC50122, which will insulate, seal, and waterproof electrical connections. I would still recommend wrapping any connections with actual electrical tape as well for extra protection. Another option is to use heat shrink tubing which is usually available just about anywhere tools and/or automotive parts are sold. With this you would first place the tubing around one of the wires before making the connection. Then use a butt...
  view full answer...


• How to Adjust Electric Drum Trailer Brakes and What Tool Should be Used
• If the trailer brakes seem weak and they are newly installed then you will need to adjust the brakes to push the shoes out a little further for optimum braking. To see how to manually adjust trailer brake assemblies check out the video I attached, fast-forward to the 4:35 mark of the video. I also recommend brake adjustment tool # W80630 which will make it easier to adjust the brakes than using a flat blade screwdriver.
  view full answer...